Fiber Access Terminal (FAT) Manufacturer in China

What is a fiber access terminal?

Fiber Access Terminal incorporate hardened connector technology that is designed to withstand the rugged outside plant environment. Hardened connectors are factory-terminated and environmentally sealed for use in optical drop cable deployments.

Kotak terminal gentian optik boleh terdiri daripada pelbagai jenis:

Berdasarkan Kaedah Sambungan Kabel

• Kotak Terminal Lurus: Kotak terminal ini mempunyai satu lubang luaran untuk saluran penerima.
• Kotak Terminal jenis bercabang: Kotak terminal ini mempunyai beberapa lubang untuk saluran penerima.

Berdasarkan bilangan gentian bercantum

Kotak terminal boleh dibahagikan kepada 2 dalam, 8 keluar, 4 dalam 24 keluar, 4 dalam 12 keluar, dsb.

Berdasarkan bahan cangkerang

Kotak terminal boleh menjadi kotak terminal gentian optik cangkang plastik atau cangkang logam.

Berdasarkan gaya

Kotak ini boleh menjadi laci rak, dipasang di dinding, jenis desktop dan jenis lain.

Indoor Fiber Access Terminal

Terminal pengedaran gentian dalaman ialah penyelesaian kotak gentian padat untuk keperluan pemasangan dalam MDU bersaiz kecil hingga sederhana, berbilang unit kediaman atau berbilang unit penyewa (MTU).

Outdoor Fiber Access Terminal

Terminal Pengedaran Gentian Luaran digunakan untuk memasang gentian dalam MDU bersaiz kecil dan sederhana, atau unit berbilang kediaman.

Custom a Fiber Access Terminal is easy here with Bativ, You need to make clear your requirements, We will send you our draft for the custom fiber optic products, Take 2 ports Fiber Access Terminal for example, We can make a 3D model for your reference until you are satisfied with it, Then we can get back to you with our best quote or sample for your quality evaluation.

Installation of the Fiber Access Terminal must be done under the supervision of a skilled technician or engineer. Here are the various stages in the installation of the FTB.

Melekap

The optical Fiber Access Terminal is mounted on the wall or on the 19 inches (483 mm) wide standard rack. The front panel should be easily accessible as the cable enters from the bottom.

Cable End Preparation

Any fiber cable’s end has to be prepared before starting the cable entry in the optical Fiber Access Terminal. The cable end preparation procedure is available from the supplier. It is crucial to protect the bare fibers at this stage. This is because they get exposed after following the cable end preparation.

Cable Entry

Once the cable ends are prepared, a rubber diaphragm at the box’s cable entry hole needs to be pierced. This is to be done before inserting the cable in the box, as this opening is blocked in new boxes. 

Cable End Clamping

The Fiber Access Terminal has several plastic fiber guide posts mounted in it. The fiber in the sleeves or transport tube of the cable is routed through them. Through these guideposts, all the excess length of the cable is brought into the selected splice tray. Then, using a plastic clamping strap, it is clamped at the splice tray’s entry point.

Splicing

The most important part of the installation process is splicing the optical fiber from the cable to the pigtails. A splicing machine is used for this purpose. It is kept close to the termination box on a table.

A stainless steel wire mechanism is released from its spring catch to open a particular splice tray. A splicing machine is used to splice the pigtail fibers so that the fiber ends come out of the cable. They are then pushed to fit into the fused splice.

The process is carried on for all the splices to be stored in splice trays. These splice trays are then placed in a stack inside the termination box. The stainless steel wire closing mechanism is then closed with the box.

It depends on the quantity you will order, Usually 1-3 days for 1000pcs, and 7-10 days for 1000-20000pcs. And 10-15 days for 20000 to 200,000pcs.

Free sample is available any time, We believe it will be a good start between us when you tested our Fiber Access Terminal samples.